Skip to main content

Full text of "Hacks and Mods"

See other formats


Automatic Garage Door Opener 



.1 



Make Projects 



build, hack, tweak, share, discover^ 



Automatic Garage Door Opener 

Written By: Miguel Marcos 

SUMMARY 

This project combines a number of unrelated technologies to provide a small convenience. 

The essence of this project is to remotely actuate a switch connected to the garage door 
opener when a GPS-enabled smartphone enters a pre-defined geographical trigger zone. 

In addition to the motorized garage door opener, the following components are used in the 
system: 

X-10 Universal Module UM506, X-10 Computer Interface CM11A, Lantronix XPort Evaluation Board, D-Link Ethernet 
Router DI-624, Android-based smartphone 



© Make Projects www.makeprojects.com Page 1 of 5 



Automatic Garage Door Opener 

Step 1 — Automatic Garage Door Opener 

• Hardware setup: 

• Setting up the hardware components is straightforward. To start with, my garage door 
opener has a connection for a manual pushbutton and thus I simply attached the relay 
contacts of the UM506 Universal Module in parallel with the pushbutton. Also, I configured 
the module for momentary closure and plugged it into a nearby AC outlet so that it can 
communicate with the CM11AX-10 Controller over the house wiring. 

• The control end of the CM1 1 A Interface is a standard RS-232 port which is normally 
connected to a PC but for this project I connected it to the RS-232 side of the Lantronix 
XPort Evaluation board (I had to build a short gender-changer adapter cable) 

• The Ethernet side of the XPort connects to my home computer network which in turn is 
connected to the Internet via an always-on, broadband connection. 

• I should point out that one could also use a PC and a simple program to bridge the RS-232 
connection of the CM11A Interface to the Internet. The Lantronix module, however, offers 
two clear advantages: lower power consumption and, more importantly, the ability to 
recover without intervention in case of a power outage. On the other hand, the software 
bridge could be designed to be highly secure. 



© Make Projects www.makeprojects.com Page 2 of 5 



Automatic Garage Door Opener 



Step 2 





., - ■-.- 







■ i l [140 



., ■"■ "' " '■: 



• Software configuration: 

• The overall software setup for this project is far from trivial mainly because of the required 
development of the App for the Android smartphone. However, the configuration of the 
hardware devices is relatively easy. 

• Lantronix XPort: 

• Because of the requisite port forwarding, the XPort module should be configured with a 
static IP address within your home network. But before you can make any configuration 
changes you will need to know the IP address assigned to the module when it is first 
attached to the network. You can go about this by using Lantronix's Device Installer utiliy. 
From this utility you can also access the device's configuration pages. 

• The relevant items to configure are: 

• Network | IP Configuration: select "Use the following IP configuration" and supply suitable 
values for the IP Address and Subnet Mask 

• Channel 1 | Serial Settings | Port Settings: the required Baud Rate for communicating with 
the CM1 1 A Interface is 4800 bps. The remainder of the fields can be left at the default 
values. 

• Channel 1 | Connection: here enter a value of your choice (or use the default) for the Local 
Port under Endpoint Configuration. You can also provide for a little bit of security by 
requiring a password to complete the incoming connection from the Internet under Passive 
Connection. 



© Make Projects 



www.makeprojects.com 



Page 3 of 5 



Automatic Garage Door Opener 



Step 3 



DI-624 




High-Speed 2.4GHz Wireless Router 



BifTi'.W 


Advanced K5I?S 




Virtual Server is 


used ro all c-v Inle-nel users actes s Is L-r ! services. 




Nairn 
PrtoaWIP 


© EnaDiea O Disanic-ci 
JCMIIA [ Clear | 

3HUQ4XXOUOH 




Protocol Type 


TCP 




pmatfl port 


556S5 




PuHicPori 


KSSS 




scneduw 


® Always 

OFrom time M_; 00 _ AM _ i 00 fl JmQ AM fl 

day Sun L to Sun Li 




Apply Cancel Help 


Name 


Prh^le IP Protocol StiiefliHe 











High-Speed 2,4GHz Wireless Router 
Tools 



C-jnainK; DNS 








COWS 

Server Address 
H*sl Name 
Usemame 
Password 


© Enabled O Disabled 






No IP com 


]myhwne,net 


1 


Mxtx&xxxa* 




















4 J O 

A ;'!!':! v t -i 11 T! Help 



• Network router: 

• A port needs to be opened and forwarded to the XPort module in order to handle the control 
requests from the smartphone. 

• The procedure for this varies slightly with the router. For the DI-624 the configuration is set 
in the Virtual Server page of the Advanced tab. 

• The other configuration change required for the router stems from the fact that IP 
addresses assigned to home users by Internet Service Providers are usually dynamic. 
That means that the address that the smartphone needs to communicate with can change 
at any time. 

• Fortunately, many routers provide a feature called Dynamic DNS. When this is enabled, 
the router automatically reports its assigned IP address to a DNS server on the Internet 
which can then match the address to a fixed friendly name such as "myhome.net". There 
may be several Dynamic DNS providers available. I have established a free, basic 
account with "www.no-ip.com" which is supported by the DI-624 

• On the DI-624, Dynamic DNS is configured on the DDNS page of the Tools tab. 



© Make Projects 



www.makeprojects.com 



Page 4 of 5 



Automatic Garage Door Opener 



Step 4 

• The final piece of software is the Android App itself. The entire source code is contained in 
the GarageDoor.pdf file. Minimal familiarity with the Android development tools is required 
to build the App. 

• The friendly URL (as obtained from the Dynamic DNS provider) of the router as well as the 
forwarded port number have to entered in the source code and, if you require a password 
to complete the connection to the XPort, then it must also be hardcoded. Likewise, the 
geographical coordinates of the trigger point must be determined and entered. A working 
version of the App can be used to retrieve those coordinates. 

• Finally, the X-10 House Code / Unit Code of the UM506 module must be entered. The 
provided source code uses A1 . The communications protocol for the CM1 1 A Interface is 
also included. 

• Suggestions for improving the App might be to add user interface features to set some or 
all of the above items. 

• Note: it is likely that you can approach you house from two different directions in which 
case you may want to provide for two trigger zones (a change to the source code is 
required). The location and radius of the trigger zone(s) may also be dictated by the speed 
at which you can approach, the update rate and accuracy of the GPS receiver, and the 
latency in X-10 communications. 

This document was last generated on 2012-11-03 04:06:22 AM. 



© Make Projects www.makeprojects.com Page 5 of 5